電動平車常見問題的解決方法

　　電動平車常見問題的解決方法

　　一、制動間隔過長。原因：制動環磨損。解決方法：調整制動螺栓或者替換制動環。

　　二、電動平車在運送重物的時候，泊車后不能再起動。原因1、系統電壓過低或動搖過大。解決方法：等電壓康復正常后再起動。原因2、電機缺相。解決方法：查看電源相數。

　　三、電動平車運行時噪聲過大。原因1、電氣控制柜毛病：反常噪聲發生在控制回路一般宣布“哼”的噪聲，大多是接觸器呈現了毛病。解決方法：對毛病接觸器進行檢修，無法檢修時替換，處理后，噪聲自行消除。原因2、減速箱毛病.解決方法：停機查看，首先確定減速器的減速箱或軸承在運用前是否加了潤滑油，運用中是否定期替換潤滑油，如沒有按要求潤滑，減速器不僅會發生過高的“嗡嗡”聲，還會過度磨損或損壞齒輪及軸承。

　　四、電機溫升過高。原因1、超載運用：超載導致電機發熱，長時間超載將焚毀電機。解決方法：電動平車載重在額外載重范圍之內。原因2、電機軸承損壞。解決方法：替換電機軸承。原因3、未規定工作制工作。解決方法：運用時應嚴厲按電機工作制工作。

　　五、電動平車無電源顯示。原因1、不通電，電系統是否對電動平車電源送電。解決方法：用試電筆測試，如沒送電，送電后再工作。原因2、缺相：驅動電機主、控回路的電器損壞、線路斷開或接觸不良，也會使平車驅動電機缺相無法正常工作。解決方法：檢修主、控回路，檢修時，為了避免主、控回路送給三相電機的電源缺相而焚毀電機，或電動平車驅動電機忽然得電工作，發生危害，要先將電機從電源線路上斷開，只給主、控回路送電，然后點動起動和中止開關，查看剖析控制電器及線路的工作狀況，對有問題的電器或線路進行替換，當承認主、控回路無毛病，方可重新試車。

• 上一篇：電動平車齒輪泵端面的修理方法
• 下一篇：電動平車定時檢查各部件的技術狀況